Network alarm system | GSM & pstn industrial Security systems | security device

Networking alarm&surveillance updated alarm systems

Industrial & commercial applicable security alarms

Communications:

1. Compatible with wired/ wireless. 6 wired zones and 6 wireless zones can be learned. Each wireless zone can expand up to 3 detectors.

2. Support CONTACT ID protocol: it makes test with alarm center terminal to guarantee the normal working of alarm system.

3. It can realize to control remotely and Arm/ Disarm to the alarm system by the software of network alarm center. (The eighth alarm telephone as the remote controlling programmable telephone).

4. Eight groups of telephones, mobile telephones and alarm center telephones can be set. Also it can set the alarm type of every group of telephone and the zone list of communication.

5. It rushes to inform you the alarm message by halting the speaking on telephone, and then recovers the speaking automatically.

6. Wired zone reaction speed (100ms-900ms) and support Normal Open, Normal Close and end-of-line resistor at freedom.

7. The trouble of telephone line and GSM module can be reacted on the keypadâ€™s buzzer or wired/ wireless siren output.

8. GSM module is for option. It is more stable by realizing PSTN and GSM double-network alarm. Alarm by double-network or only by GSM network when telephone line is cut off.

8. It can realize sound and SIM message alarm and support ADEMCO CID center.

Automations:

1. The system can be expanded to 4 keypads and each keypad with a wired zone.

2. Access codes: 1 installer code + 4 master codes + 4 users code.

3. With Door Close Automatically Arm function.

4. Support report of patrolling.

5. Home Arm and Overall Arm. The zones list of Home Arm can be defined at will.

6. One group of NC & NO relay output interface to set various alarm output.

7. It can reduce the false alarm rate by judging the logic function between the crossover zones.

8. Remote Arm, Disarm and on-site alarm setup on the preserved telephones, mobile phones or the telephones connected with panel.

9. Both AC220V and 12V, 7Ah rechargeable battery power supplied and switched each other automatically. The low battery can reminder the host. The design of power-output limitation is to protect the electronic circuit.

10. The Real-time module endows the system with two timers can be set to Arm/ Disarm independently according to the arrangement of the working days and resting days. Every timer can set Arm/ Disarm of each zone independently.

8. SD module is for option. It can monitor the on-site alarm status. It can link and record the alarm on-site. Then store it into SD card.

8. Wired board is for option. It is convenient for guard to check the alarm status during patrol.

Specifications:
Input Voltage:	AC 220V Â±15% 50Hz	Backup Battery :	12V/7Ah	Assistant Output Current:	ï¼œ500mA
System Output Current:	â‰¤800mA	Frequency:	433.92MHz	Communication Distance between wireless PIR detector and alarm panel:	â‰¥500m in the open area
Communication Distance between wireless remote controller and alarm panel:	â‰¥300m in the open area	Communication Distance between wireless siren and alarm panel:	â‰¥300m in the open area	Dimension	25826077 mm
Weight:	2.8 kg

Items included in standard set:

1pc KB-A1188 alarm panel, 4pcs KB-A32 Keypads.

Other accessories for optional:

SS-168 wireless smoke sensor, KS-21AF transeiver, KS-307DCT Wireless PIR detector, KS-21AW motion sensor, KS-306FCT curtain infrared detector, KS-208T outdoor detector, KS-70A indoor siren, KS-70B outdoor siren, MT-338A-E4 Wireless Gas Sensor, wired detectors etc.

Network alarm system | GSM & pstn industrial Security systems | security device

About the Webstore Sensors & Motion Detectors category: